Axial Flow Fans

Used for :

• Moving Air Against High Static Pressure

• To Exhaust Hot Air & Corrosive Gases

Technicalities :

• Designed in line and mixed flow blowers

• Bifurcated housings that exhaust hot air, corrosive gases etc

• Motor is isolated from destructive heat & fumes in a separate chamber Remains cool even after extended operation

• Only moving part is exposed to heat

Applications :

• Glass Industries

• Food processing Industries

• Chemical Industries

• Pulp & paper Industries

• Steel Industries

Construction :
The cylindrical casing of fans is fabricated from mild steel plates or stainless steel with adequate size for fine clearances as is practicable for better efficiency and fitted with flanges on both the ends. Foot mounting arrangements to facilitate installation of the fan, on the ground of frame look.


Impeller :
The impeller of axial flow fan is made of cast in aluminum alloy and dynamically balanced and aero foil of blade is designed to have maximum efficiency at lesser motor Power.

Motors :
The standard make A.C motors are totally enclosed squirrel cage induction type suitable for ambient temperature up to 40° C. Flame proofs ( IIA/IIB/IIC) , vapor tight, Class F, Class H and other motors can also be supplied on request.

Bearing :
Ball or Ball and roller bearings are fitted as standard.

Driving Arrangements :
There are two types of drives – The direct drive arrangement or V – Belt drive arrangement.

The direct drive arrangement, impeller and motor are both housed inside the casing and impeller is directly mounted or motor shaft.

V. Belt Arrangement – The impeller mounted on a separate shaft supported on two ball bearings and Plummer blocks inside casing. The motor is mounted on outer ring of the casing and shaft is driven with V- Belts.

Hot Air & Gas Application :
Fan is suitable for air and gas up to temperature of 65° C. or Between 65° C and 150° C the fans are made up of V – Belt drive arrangement and are equipped with special high temperature lubricated ball bearings.

Technical specification

• Available with Fixed & Variable Pitches Impeller
• Larger sizes also available on demand.

Salient Features:

• Cost effective
• Large air volumes
• Low power consumption
• Easy to install
• Low maintenance
• Can be connected to Duct

Extra Features on Request

• Available in Direct Drive & V-Belt Drive
• Long and short casing
• F.R.P/rubber lined for corrosive area
• Gravity Louver/Bird Guard (Front/Back)
• Special Paint Finish
• Motor Class ( FLP With IIA, IIB IIC or Class F, Class H ect.)
• Any Special stand

Construction :
The Cylindrical casing of fans is fabricated from mild steel plates or Stainless Steel with adequate size for fine clearances as is practicable for better efficiency and fitted with Flanges on both the ends. Foot mounting arrangements to facilitate installation of the fan, on the ground of frame look.

Impeller :

The impeller of axial flow fan is made of cast in aluminium alloy and dynamically balanced and aerofoil of blade is designed to have maximum efficiency at lesser motor Power.

Motors :
The standard make A.C motors are totally enclosed squirrel cage induction type suitable for ambient temperature up to 40° C. Flame proofs ( IIA/IIB/IIC) , vapor tight, Class F, Class H and other motors can also be supplied on request.

Bearing :
Ball or Ball and roller bearings are fitted as standard.

Driving Arrangements :
There are two types of drives – The direct drive arrangement or V – Belt drive arrangement.

The direct drive arrangement, impeller and motor are both housed inside the casing and impeller is directly mounted or motor shaft.

V. Belt Arrangement – The impeller mounted on a separate shaft supported on two ball bearings and Plummer blocks inside casing. The motor is mounted on outer ring of the casing and shaft is driven with V- Belts.

Hot Air & Gas Application :
Fan is suitable for air and gas up to temperature of 65° C. or Between 65° C and 150° C the fans are made up of V – Belt drive arrangement and are equipped with special high temperature lubricated ball bearings.

Technical specification

• Air Volume up to 150000 C.M.H

• Sizes from 300 mm to 1600 mm.*

• Available 4,6,7,8 & 11 Blades Impeller

• Available with Fixed & Variable Pitches Impeller

• *Larger sizes also available on demand.

Salient Features:

• Cost effective

• Large air volumes

• Low power consumption

• Easy to install

• Low maintenance

• Can be connected to Duct

Extra Features on Request

• Available in Direct Drive & V-Belt Drive

• Long and short casing

• F.R.P/rubber lined for corrosive area

• Gravity Louver/Bird Guard (Front/Back)

• Special Paint Finish

• Motor Class ( FLP With IIA,IIB IIC or Class F, Class H ect.)

• Any Special stand

Construction :
The Cylindrical casing of fans is fabricated from mild steel plates or Stainless Steel with adequate size for fine clearances as is practicable for better efficiency and fitted with Flanges on both the ends. Foot mounting arrangements to facilitate installation of the fan, on the ground of frame look.

Impeller :

The impeller of axial flow fan is made of cast in aluminium alloy and dynamically balanced and aerofoil of blade is designed to have maximum efficiency at lesser motor Power.

Motors :
The standard make A.C motors are totally enclosed squirrel cage induction type suitable for ambient temperature up to 40° C. Flame proofs ( IIA/IIB/IIC) , vapor tight, Class F, Class H and other motors can also be supplied on request.

Bearing :
Ball or Ball and roller bearings are fitted as standard.

Driving Arrangements :
There are two types of drives – The direct drive arrangement or V – Belt drive arrangement.

The direct drive arrangement, impeller and motor are both housed inside the casing and impeller is directly mounted or motor shaft.

V. Belt Arrangement – The impeller mounted on a separate shaft supported on two ball bearings and Plummer blocks inside casing. The motor is mounted on outer ring of the casing and shaft is driven with V- Belts.

Hot Air & Gas Application :
Fan is suitable for air and gas up to temperature of 65° C. or Between 65° C and 150° C the fans are made up of V – Belt drive arrangement and are equipped with special high temperature lubricated ball bearings.

Technical specification

• Air Volume up to 150000 C.M.H

• Sizes from 300 mm to 1600 mm.*

• Available 4,6,7,8 & 11 Blades Impeller

• Available with Fixed & Variable Pitches Impeller

• Larger sizes also available on demand.

Salient Features:

• Cost effective

• Large air volumes

• Low power consumption

• Easy to install

• Low maintenance

• Can be connected to Duct

Extra Features on Request

• Available in Direct Drive & V-Belt Drive

• Long and short casing

• F.R.P/rubber lined for corrosive area

• Gravity Louver/Bird Guard (Front/Back)

• Special Paint Finish

• Motor Class ( FLP With IIA,IIB IIC or Class F, Class H ect.)

• Any Special stand

Construction :
The Cylindrical casing of fans is fabricated from mild steel plates or Stainless Steel with adequate size for fine clearances as is practicable for better efficiency and fitted with Flanges on both the ends. Foot mounting arrangements to facilitate installation of the fan, on the ground of frame look.

Impeller :

The impeller of axial flow fan is made of cast in aluminium alloy and dynamically balanced and aerofoil of blade is designed to have maximum efficiency at lesser motor Power.

Motors :
The standard make A.C motors are totally enclosed squirrel cage induction type suitable for ambient temperature up to 40° C. Flame proofs ( IIA/IIB/IIC) , vapor tight, Class F, Class H and other motors can also be supplied on request.

Bearing :
Ball or Ball and roller bearings are fitted as standard.

Driving Arrangements :
There are two types of drives – The direct drive arrangement or V – Belt drive arrangement.

The direct drive arrangement, impeller and motor are both housed inside the casing and impeller is directly mounted or motor shaft.

V. Belt Arrangement – The impeller mounted on a separate shaft supported on two ball bearings and Plummer blocks inside casing. The motor is mounted on outer ring of the casing and shaft is driven with V- Belts.

Hot Air & Gas Application :
Fan is suitable for air and gas up to temperature of 65° C. or Between 65° C and 150° C the fans are made up of V – Belt drive arrangement and are equipped with special high temperature lubricated ball bearings.

Technical specification

• Air Volume up to 150000 C.M.H

• Sizes from 300 mm to 1600 mm.*

• Available 4,6,7,8 & 11 Blades Impeller

• Available with Fixed & Variable Pitches Impeller

• Larger sizes also available on demand.

Salient Features:

• Cost effective

• Large air volumes

• Low power consumption

• Easy to install

• Low maintenance

• Can be connected to Duct

Extra Features on Request

• Available in Direct Drive & V-Belt Drive

• Long and short casing

• F.R.P/rubber lined for corrosive area

• Gravity Louver/Bird Guard (Front/Back)

• Special Paint Finish

• Motor Class ( FLP With IIA,IIB IIC or Class F, Class H ect.)

• Any Special stand

Construction :
The Cylindrical casing of fans is fabricated from mild steel plates or Stainless Steel with adequate size for fine clearances as is practicable for better efficiency and fitted with Flanges on both the ends. Foot mounting arrangements to facilitate installation of the fan, on the ground of frame look.

Impeller :

The impeller of axial flow fan is made of cast in aluminium alloy and dynamically balanced and aerofoil of blade is designed to have maximum efficiency at lesser motor Power.

Motors :
The standard make A.C motors are totally enclosed squirrel cage induction type suitable for ambient temperature up to 40° C. Flame proofs ( IIA/IIB/IIC) , vapor tight, Class F, Class H and other motors can also be supplied on request.

Bearing :
Ball or Ball and roller bearings are fitted as standard.

Driving Arrangements :
There are two types of drives – The direct drive arrangement or V – Belt drive arrangement.

The direct drive arrangement, impeller and motor are both housed inside the casing and impeller is directly mounted or motor shaft.

V. Belt Arrangement – The impeller mounted on a separate shaft supported on two ball bearings and Plummer blocks inside casing. The motor is mounted on outer ring of the casing and shaft is driven with V- Belts.

Hot Air & Gas Application :
Fan is suitable for air and gas up to temperature of 65° C. or Between 65° C and 150° C the fans are made up of V – Belt drive arrangement and are equipped with special high temperature lubricated ball bearings.

Technical specification

• Air Volume up to 150000 C.M.H

• Sizes from 300 mm to 1600 mm.*

• Available 4,6,7,8 & 11 Blades Impeller

• Available with Fixed & Variable Pitches Impeller

• Larger sizes also available on demand.

Salient Features:

• Cost effective

• Large air volumes

• Low power consumption

• Easy to install

• Low maintenance

• Can be connected to Duct

Extra Features on Request

• Available in Direct Drive & V-Belt Drive

• Long and short casing

• F.R.P/rubber lined for corrosive area

• Gravity Louver/Bird Guard (Front/Back)

• Special Paint Finish

• Motor Class ( FLP With IIA,IIB IIC or Class F, Class H ect.)

• Any Special stand

Construction :
The Cylindrical casing of fans is fabricated from mild steel plates or Stainless Steel with adequate size for fine clearances as is practicable for better efficiency and fitted with Flanges on both the ends. Foot mounting arrangements to facilitate installation of the fan, on the ground of frame look.

Impeller :

The impeller of axial flow fan is made of cast in aluminium alloy and dynamically balanced and aerofoil of blade is designed to have maximum efficiency at lesser motor Power.

Motors :
The standard make A.C motors are totally enclosed squirrel cage induction type suitable for ambient temperature up to 40° C. Flame proofs ( IIA/IIB/IIC) , vapor tight, Class F, Class H and other motors can also be supplied on request.

Bearing :
Ball or Ball and roller bearings are fitted as standard.

Driving Arrangements :
There are two types of drives – The direct drive arrangement or V – Belt drive arrangement.

The direct drive arrangement, impeller and motor are both housed inside the casing and impeller is directly mounted or motor shaft.

V. Belt Arrangement – The impeller mounted on a separate shaft supported on two ball bearings and Plummer blocks inside casing. The motor is mounted on outer ring of the casing and shaft is driven with V- Belts.

Hot Air & Gas Application :
Fan is suitable for air and gas up to temperature of 65° C. or Between 65° C and 150° C the fans are made up of V – Belt drive arrangement and are equipped with special high temperature lubricated ball bearings.

Technical specification

• Air Volume up to 150000 C.M.H

• Sizes from 300 mm to 1600 mm.*

• Available 4,6,7,8 & 11 Blades Impeller

• Available with Fixed & Variable Pitches Impeller

• Larger sizes also available on demand.

Salient Features:

• Cost effective

• Large air volumes

• Low power consumption

• Easy to install

• Low maintenance

• Can be connected to Duct

Extra Features on Request

• Available in Direct Drive & V-Belt Drive

• Long and short casing

• F.R.P/rubber lined for corrosive area

• Gravity Louver/Bird Guard (Front/Back)

• Special Paint Finish

• Motor Class ( FLP With IIA,IIB IIC or Class F, Class H ect.)

• Any Special stand

Construction :
The Cylindrical casing of fans is fabricated from mild steel plates or Stainless Steel with adequate size for fine clearances as is practicable for better efficiency and fitted with Flanges on both the ends. Foot mounting arrangements to facilitate installation of the fan, on the ground of frame look.

Impeller :

The impeller of axial flow fan is made of cast in aluminium alloy and dynamically balanced and aerofoil of blade is designed to have maximum efficiency at lesser motor Power.

Motors :
The standard make A.C motors are totally enclosed squirrel cage induction type suitable for ambient temperature up to 40° C. Flame proofs ( IIA/IIB/IIC) , vapor tight, Class F, Class H and other motors can also be supplied on request.

Bearing :
Ball or Ball and roller bearings are fitted as standard.

Driving Arrangements :
There are two types of drives – The direct drive arrangement or V – Belt drive arrangement.

The direct drive arrangement, impeller and motor are both housed inside the casing and impeller is directly mounted or motor shaft.

V. Belt Arrangement – The impeller mounted on a separate shaft supported on two ball bearings and Plummer blocks inside casing. The motor is mounted on outer ring of the casing and shaft is driven with V- Belts.

Hot Air & Gas Application :
Fan is suitable for air and gas up to temperature of 65° C. or Between 65° C and 150° C the fans are made up of V – Belt drive arrangement and are equipped with special high temperature lubricated ball bearings.

Technical specification

• Air Volume up to 150000 C.M.H

• Sizes from 300 mm to 1600 mm.*

• Available 4,6,7,8 & 11 Blades Impeller

• Available with Fixed & Variable Pitches Impeller

• Larger sizes also available on demand.

Salient Features:

• Cost effective

• Large air volumes

• Low power consumption

• Easy to install

• Low maintenance

• Can be connected to Duct

Extra Features on Request

• Available in Direct Drive & V-Belt Drive

• Long and short casing

• F.R.P/rubber lined for corrosive area

• Gravity Louver/Bird Guard (Front/Back)

• Special Paint Finish

• Motor Class ( FLP With IIA,IIB IIC or Class F, Class H ect.)

• Any Special stand

Construction :
The Cylindrical casing of fans is fabricated from mild steel plates or Stainless Steel with adequate size for fine clearances as is practicable for better efficiency and fitted with Flanges on both the ends. Foot mounting arrangements to facilitate installation of the fan, on the ground of frame look.

Impeller :

The impeller of axial flow fan is made of cast in aluminium alloy and dynamically balanced and aerofoil of blade is designed to have maximum efficiency at lesser motor Power.

Motors :
The standard make A.C motors are totally enclosed squirrel cage induction type suitable for ambient temperature up to 40° C. Flame proofs ( IIA/IIB/IIC) , vapor tight, Class F, Class H and other motors can also be supplied on request.

Bearing :
Ball or Ball and roller bearings are fitted as standard.

Driving Arrangements :
There are two types of drives – The direct drive arrangement or V – Belt drive arrangement.

The direct drive arrangement, impeller and motor are both housed inside the casing and impeller is directly mounted or motor shaft.

V. Belt Arrangement – The impeller mounted on a separate shaft supported on two ball bearings and Plummer blocks inside casing. The motor is mounted on outer ring of the casing and shaft is driven with V- Belts.

Hot Air & Gas Application :
Fan is suitable for air and gas up to temperature of 65° C. or Between 65° C and 150° C the fans are made up of V – Belt drive arrangement and are equipped with special high temperature lubricated ball bearings.

Technical specification

• Air Volume up to 150000 C.M.H

• Sizes from 300 mm to 1600 mm.*

• Available 4,6,7,8 & 11 Blades Impeller

• Available with Fixed & Variable Pitches Impeller

• Larger sizes also available on demand.

Salient Features:

• Cost effective

• Large air volumes

• Low power consumption

• Easy to install

• Low maintenance

• Can be connected to Duct

Extra Features on Request

• Available in Direct Drive & V-Belt Drive

• Long and short casing

• F.R.P/rubber lined for corrosive area

• Gravity Louver/Bird Guard (Front/Back)

• Special Paint Finish

• Motor Class ( FLP With IIA,IIB IIC or Class F, Class H ect.)

• Any Special stand